Rebuild List: Engine List Crankcase
-
Lambretta Engine Casing, Large block, 200cc (comes with endplate but no engine mounts) (crankcase) SILMBL1691£447.77 £373.14SIL latest NOS Lambretta Large block 200cc engine casing. Comes with matching end plate. Engine mounting are extra. We can also port casings to suit your cylinder, bead blast an... Learn MoreYou'll need: 1 of these
-
Lambretta Engine mountings, uprated left and right hand fitting, pair, stainless steel, Li, Tv, Sx, Gp, Race-Tour MBMBGM0302£50.35 £41.96A pair of MB uprated stainless steel Lambretta engine mounts (silent blocks). Fits all Lambretta engine casings - Series I, 2, 3. Both engine mounts are marked up with larg... Learn MoreYou'll need: 1 of these
-
Lambretta Engine mounts, pair, Gp, Sx, Tv, bgmMBL1687£43.50 £36.25BGM made Lambretta series 3 and GP large engine mount set, originally fitted to series 3 TV/Special/SX and DL/GP models. The right hand mount is re-inforced to take the extra stra... Learn MoreYou'll need: 1 of these
-
Lambretta Engine bump stop rubber, Viton, MBMBL0155£7.45 £6.21This rubber item sits in a hole on the top of your casing and supports your frame on your engine when the rear shocker is fuly compressed or removed. This version is made from Vit... Learn MoreYou'll need: 1 of these
-
Lambretta Engine bump stop washer, stainless steel, MBMBP0274£2.36 £1.97MB Remade engine bump stop washer in stainless steel No more rusted up washers that are hard to remove from the casing any more!... Learn MoreYou'll need: 1 of these
-
Gasket, Lambretta crankcase side, 0.8mm, standard thickness, MBMBP0181£4.69 £3.91This is a top quality reuseable - standard thickness 0.8mm crankcase side gasket. Fit all Series 1, 2 or 3 crankcase sides (except TV Series 1) Another MB made product.... Learn MoreYou'll need: 1 of these
-
Gasket, Lambretta crankcase side, 1.2mm, thicker type, MBMBP0485£5.80 £4.83This is a quality reuseable - upgraded thicker 1.2mm crankcase side gasket to fit all Series 1, 2 or 3 crankcase sides (except TV Series 1) Ideal if your side casing face is prone... Learn MoreYou'll need: 1 of these
-
Gasket Lambretta drive side (plate) high strength fuel resistant, White, Race-Tour MBMBP0645£5.68 £4.73Made for MB this is a fuel and heat resistant drive plate gasket.It fits between the drive bearing and the drive side seal plate. Always use some fuel resistant sealer. The best ... Learn MoreYou'll need: 1 of these
-
Lambretta Drive side plate high tensile allen screw kit (set of 4)MBP0210K£0.62 £0.52If you've ever taken apart a Lambretta engine you will have struggled to undo the 4 screws that hold the drive side seal plate in place. The slot for the screwdriver may have been... Learn MoreYou'll need: 1 of these
-
Lambretta Drive side steel plate, Race-Tour MBMBP0085£8.82 £7.35Alloy drive side seal plates are much lighter than steel plates but do to tend warp. Our steel plates are redesigned by Mark Broadhurst 0.7mm thinner so the screws and plate doesn... Learn MoreYou'll need: 1 of these
-
Lambretta Engine drive seal, Viton, Race-Tour MBMBP0007£5.51 £4.59This is a specially made MB Race-Tour Drive side Viton seal. Viton resists modern fuels so will not break down in use. TOP TIP always grease and oil both the crank drive sho... Learn MoreYou'll need: 1 of these
-
Lambretta Engine oil seal kit (set of 5) Viton, Race-Tour MBMBL0545K£23.62 £19.68This handy engine oil seal kit contains: Drive side - In Viton Small magneto - In Viton Large magneto - In Viton Kick start - In Viton Rear hub seal - In V... Learn MoreYou'll need: 1 of these
-
Lambretta Engine rear hub seal, Race-Tour MBMBB0074£4.42 £3.68A high quality rear hub seal. Fits all Series 1, 2 and 3 Lambretta rear hub bearings. ... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing set, Drive side, touring (bearing, plate, gasket, screws, seal) Race-Tour MB brandMBP0639K£28.88 £24.07Drive side bearing kit, MB Drive bearing, touring MB Drive side Viton oil seal, MB Drive side seal plate gasket, MB Drive side seal plate, steel, MB Drive screws, hi... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing set, Drive side, touring (bearing, plate, gasket, screws, seal) name brandMBP0640K£35.50 £29.58Drive side bearing kit, MB Drive bearing, touring, named brand Drive side Viton oil seal, MB Drive side seal plate gasket, MB Drive side seal plate, steel, MB Drive sc... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing set, Drive side, standard (bearing, plate, gasket, screws, seal) name brandMBL1652K£29.08 £24.23Top quality branded (usualy SKF, FAG) standard drive side bearing. Steel Drive plate, thinner no rubbing, MB Drive seal, Viton, MB Drive side halite washer, MB Drive screws, ... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing, Drive side touring type with extra seal, name brandMBB0031£14.87 £12.39A high quality Touring Road drive bearing to suit all Series 1, 2 and 3 engine casings. MB were the first to introduce this single sealed type bearing. The seal faces the cranksh... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing, Drive side, touring type with extra seal, Race-Tour MB brandMBP0438£8.26 £6.88A high quality, drive side touring type main bearing with the extra drive seal fitted, the seal faces the crank, this helps taking the pressure off the normal drive seal which you ... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing, Drive side, name brandMBB0030£8.45 £7.04A high load quality standard drive bearing to suit all Series 1, 2 and 3 engine casings. SKF or FAG... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing, Drive side, Race-Tour MB BrandMBP0666£7.24 £6.03A high load quality MB Race-Tour standard drive bearing to suit all Series 1, 2 and 3 engine casings... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing set, Flywheel side (mag housing) Gp200, name brandMBL1654K£48.97 £40.81High load branded flywheel bearing fat type Gp200 (usually FAG, SKF) Viton Large mag seal, MB Nylon Small mag seal, MB Disc washer, MB Mag circlip ... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing set, Flywheel side (mag housing) Gp200, Race-Tour MB brandMBP0489K£37.21 £31.01High load Race-Tour flywheel bearing, fat type Gp200, MB Viton Large mag seal, MB Nylon Small mag seal, MB Disc washer, MB Mag circlip ... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing set, Flywheel side (mag housing) Li, Sx, Tv, Gp125/150, name brandMBL1653K£41.14 £34.28High load branded flywheel bearing thin type Li, Sx, Tv, Gp125/150 (usually FAG, SKF) Viton Large mag seal, MB Nylon Small mag seal, MB Disc washer, MB Mag spacer, MB ... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing set, Flywheel side (mag housing) Li, Sx, Tv, Gp125/150, Race-Tour MB brandMBP0488K£32.77 £27.31High load Race-Tour flywheel bearing, thin type Li, Sx, Tv, Gp125/150 Viton Large mag seal, MB Nylon Small mag seal, MB Disc washer, MB Mag spacer, MB Mag circlip ... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing, Flywheel, Li, Sx, Tv, Gp125, Race-Tour MB brandMBP0451£15.58 £12.98A high quality, high load flywheel bearing to suit all Li, Tv, Sx, Gp125/150 crankshafts. Increasing our own brand of bearings marked with MB Race-Tour, these are reduced in priced... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing and seal set, complete using brass clutch bush, Gp200, Race-Tour MB brandMBL1656K£125.10 £104.25This kit contains all the bearings and seals needed for a complete engine rebuild.It comprises of:- Flywheel bearing, GP200, MB Drive bearing, touring type, MB End plate rolle... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing and seal set, complete using brass clutch bush, Li, Sx, Tv, Gp125/150, Race-Tour MB brandMBL1659K£123.08 £102.57This kit contains all the bearings and seals needed for a complete engine rebuild.It comprises of:- Flywheel bearing, GP125,LI,SX,TV, MB Drive bearing, touring type, MB End pl... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing and seal set, complete using clutch needles, Li, Sx, Tv, Gp125/150, Race-Tour MB brandMBL1658K£115.58 £96.32This kit contains all the bearings and seals needed for a complete engine rebuild.It comprises of:- Flywheel bearing, GP125/LI,SX,TV, MB Drive bearing, touring type, MB End pl... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing and seal set, complete using clutch needles, Gp200, Race-Tour MB brandMBL1657K£123.53 £102.94This kit contains all the bearings and seals needed for a complete engine rebuild.It comprises of:- Flywheel bearing, GP200, MB Drive bearing, touring type, MB End plate rolle... Learn MoreYou'll need: 1 of these
-
Lambretta Bearing set, Crankshaft (mag/drive bearings, seals gaskets, plate) Gp200, Race-Tour MB brandMBP0236K£82.96 £69.13This kit contains all the parts you would need when changing your crank to any Gp200 type crankshaft. All parts are made by MB Scooters It comprises: High load, flywheel bea... Learn MoreYou'll need: 1 of these
-
Lambretta Crankcase side fastener kit, nyloc nut and washers, standard length studs, stainless steel, MBMBP0216K£17.41 £14.51This is a full set of stainless steel studs, with nyloc nuts and plain washers to secure your crankcase side. 14 x 6mm crankcase side studs, MB 1 x 6mm tailpipe stud, MB (for c... Learn MoreYou'll need: 1 of these
-
Lambretta Crankcase side, Stud kit (set) 14 x 6x37mm, 2 x 8x45mm, stainless steel, MBMBP0500K£13.73 £11.44This is a full set of stainless steel studs, made for MB Scooters Ltd 14 x 6mm crankcase side studs, MB 1 x 6mm tailpipe stud, MB (for clubman exhausts) 2 x 8mm exhaust studs,... Learn MoreYou'll need: 1 of these
-
Lambretta Crankcase side fastener kit, allen cap head, stainless steelMBP0215K£15.19 £12.66This is set of stainless steel Allen head screws and washers to secure your crankcase side.... Learn MoreYou'll need: 1 of these
-
Lambretta Crankcase side fastener kit, dome nuts, washers and studs, stainless steelMBP0234K£23.05 £19.21This is a full set of stainless steel studs, with nuts made for MB Scooters Ltd 14 x 6mm crankcase side studs, MB 1 x 6mm tailpipe stud, MB (for clubman exhausts) 14 x 6mm Dom... Learn MoreYou'll need: 1 of these
-
Lambretta Crankcase side fastener kit, studs and flange deep nuts, stainless steel, MBMBP0227K£33.06 £27.55This is a full set of stainless steel studs, with nuts made for MB Scooters Ltd 14 x 6mm crankcase side studs, MB 1 x 6mm tailpipe stud, MB (for clubman exhausts) 14 x 6mm MB ... Learn MoreYou'll need: 1 of these
-
Lambretta Crankcase side fastener kit, allen cap head, for extended 6 plate, stainless steelMBP0218K£15.58 £12.98This is set of allen head screw and washers to secure your crankcase side. The screws are longer to allow the use of a 10mm thick crankcase side packing plate.... Learn MoreYou'll need: 1 of these
-
Stud 6x21mm - 7x4x10mm, Lambretta rear hub plate, linkage tie bar, stainless steel, MBMBFST6X21SS£1.15 £0.96This stainless steel stud is designed to fit on the casing where the rear hub bearing sits and holds on the plate which holds the rear hub bearing in. You need four per casing. ... Learn MoreYou'll need: 4 of these
-
Stud 6x37mm - 16x10x11mm, Lambretta crankcase side, stainless steel, MBMBFST6X33SS£0.70 £0.58This stud is for the crankcase side, you need 14 for most crankcases. If youre using a Clubman then you use 13 and the longer tailpipe stud.We've redesigned these so the long end ... Learn MoreYou'll need: 14 of these
-
Stud 6x25mm - 10x5x10mm, Lambretta magneto housing, stainless steel, MBMBFST6X25SS£0.84 £0.70This remade stainless steel stud is designed to be used to secure the magneto housing to the engine casing. It can also be used with our adjuster block to attach that to the cas... Learn MoreYou'll need: 3 of these
-
Stud 6x33mm - 6x6x21mm, Lambretta crankcase side and TS1 inlet manifold, engineers, stainless steel, MBMBFST6X33TS1£1.44 £1.20This stud can be used to secure the crankcase side but is also as used as an inlet stud on our TS1 manifolds. It is made from stainless steel. 6mm x 6 - 6 - 21mm... Learn MoreYou'll need: 1 of these
-
Stud 6x37mm - 12x13x15mm, Lambretta crankcase side tail pipe, stainless steel, MBMBFST6X37SS£0.78 £0.65This remade stainless steel stud is used to secure the crankcase side at the point below the kick-start when standard exhausts mount to the casing. 6mm x 12 - 13 - 12mm... Learn MoreYou'll need: 1 of these
-
Stud 6x42mm - 11x20x11mm, Lambretta crankcase side with external 6 plate clutch, stainless steel, MBMBFST6X42SS£1.33 £1.11This remade stainless steel stud is designed to be used to secure the crankcase side where a 10mm thick pack plate has been used. You would need 14 per engine casing. It can also ... Learn MoreYou'll need: 14 of these
-
Stud 8x45mm - 17x11x17mm, Lambretta crankcase side exhaust mount, stainless steel, MBMBFST8X45SS£1.07 £0.89This stud is used to hold the exhaust bracket to the main engine casing. You need two per engine casing. 8mm x 17 - 11 - 17mm... Learn MoreYou'll need: 2 of these
-
Lambretta Stepped stud, 6 to 7mm - 17x13x11mm, Lambretta crankcase side tailpipe, stainless steel, MBMBP0395£4.06 £3.38A stainless steel stepped 7mm to 6mm oversized stud to repair a damaged crankcase side tailpipe 6mm thread. If the thread has gone you could fit a Timesert or helicoil, these cost... Learn MoreYou'll need: 1 of these
-
Lambretta Stepped stud, 6 to 8mm - 17x13x11mm, Lambretta crankcase side tail pipe, stainless steel, MBMBP0278£2.84 £2.37A really simple idea from Mark Broadhurst This Stainless Steel steppped stud can repair the lower exhaust tailpipe thread that usually pulls outs. Most people dont have a Hei... Learn MoreYou'll need: 1 of these
-
Lambretta Stepped stud, 6 to 7mm - 17x10x11mm, Lambretta crankcase side, stainless steel, MBMBP0394£2.84 £2.37A stainless steel stepped 7mm to 6mm oversized stud to repair a damaged crankcase side 6mm thread. If the thread has gone you could fit a Timesert or helicoil, these cost money, h... Learn MoreYou'll need: 1 of these
-
Lambretta Stepped stud, 6 to 8mm - 17x10x11mm, Lambretta crankcase side, stainless steel, MBMBP0302£4.06 £3.38A really simple idea from Mark Broadhurst This Stainless Steel steppped stud can repair all the crankcase side 6mm threads that usually pulls outs. Most people dont have a He... Learn MoreYou'll need: 1 of these
-
Lambretta Stepped stud, 8 to 10mm - 20x11x17mm, Lambretta crankcase side swan-neck, stainless steel, MBMBP0392£1.90 £1.58A MB stepped oversized stud to repair a damaged crankcase side 8mm thread. If the thread has gone you could fit a Timesert or helicoil, but these cost more money, here is a simple... Learn MoreYou'll need: 1 of these
-
Lambretta Stepped stud, 8 to 12mm - 20x11x17mm, Lambretta crankcase side swan neck stainless steel, MBMBP0393£4.06 £3.38A super over sized stepped stud from 12mm to 8mm to repair a damaged crankcase side 8mm thread that has been over tapped out. If the thread has gone and is too big to fit a Timese... Learn MoreYou'll need: 1 of these
-
Washer wavy 6mm, stainless steelMBFWW6£0.10 £0.08This fastener has universal applications but is mainly used on Lambretta crankcase sides.... Learn MoreYou'll need: 4 of these
-
Nut nyloc 6mm, stainless steelMBFNY6£0.19 £0.16This fastener has universal applications.... Learn MoreYou'll need: 1 of these
-
Screw dome allen cap 6x25mm, Lambretta for stator and crankcase sides, high tensile, Zinc platedMBFDAC6X25ZC£0.19 £0.16Amongst many applications this fastener can specifically be used on all types of flywheels where clearance is tight.It can also be used on the gearbox wishbone, TS1 inlet manifolds... Learn MoreYou'll need: 1 of these