Rebuild List: Engine List Engine Tooling
-
Tool, Allen key 3mm, Lambretta MB gear trunnionsMBL0698£0.74 £0.62Many uses for this allen key including MB remade gear trunnions.... Learn MoreYou'll need: 1 of these
-
Tool, Allen key 3.5mm, Lambretta Italian gear trunnionsMBL0007£2.04 £1.70This is the unusually sized allen key you need for most gear and clutch cable trunnion on a Lambretta.... Learn MoreYou'll need: 1 of these
-
Tool, Allen key 4mmMBL0699£0.74 £0.62Many uses for this allen key.... Learn MoreYou'll need: 1 of these
-
Tool, Allen key 5mmMBL1611£0.70 £0.58Universal Tool, 5mm Allen key... Learn MoreYou'll need: 1 of these
-
Tool, Allen key 6mmMBL0701£1.08 £0.90Universal Tool, 6mm Allen key... Learn MoreYou'll need: 1 of these
-
Tool, Allen key 7mmMBL1612£1.08 £0.90Universal Tool, 7mm Allen key.... Learn MoreYou'll need: 1 of these
-
Tool, Allen key 8mm, Lambretta headset clampMBL0702£1.67 £1.39Universal Tool, 8mm Allen key which fits Lambretta headset clamp screw.... Learn MoreYou'll need: 1 of these
-
Tool, Allen key 10mm, Lambretta crankcase side drain plugMBL0703£5.40 £4.50This 10mm allen key can be used for the crankcase side drain and level plugs amongst other things.... Learn MoreYou'll need: 1 of these
-
Tool, Allen key 12mm, Lambretta kickstart return screwMBL0704£4.00 £3.33This large 12mm allen key fits the kickstart return allen screw on most Lambrettas apart from the Indian version using a plastic sleeve which is 10mm.... Learn MoreYou'll need: 1 of these
-
Tool, Blank carb, 25/30mm, for use with pressure testers, MBMBP0668£11.22 £9.35This is a MB dual perpose carb inlet manifold blank to suit 22/24/25/26mm Dellortos and 26/28/30mm Dellortos to blank off the inlet manifold as part of our leak test kit.... Learn MoreYou'll need: 1 of these
-
Tool, Blank carb, 34/35mm, for use with pressure testers, MBMBP0669£11.86 £9.88This is a MB dual perpose carb inlet manifold blank to suit 35mm TMX Mikunis and 34/36/39mm Dellorto VHSB carbs to use in a leak test kit. ... Learn MoreYou'll need: 1 of these
-
Tool, Blank exhaust Oval, for use with pressure testers, MBMBP0670K£11.09 £9.24MB designed exhaust flange alloy blank to use with pressure test kits. Comes part of our test kit. ... Learn MoreYou'll need: 1 of these
-
Tool, Blank exhaust Round, for use with pressure testers, MBMBP0671K£11.05 £9.21MB designed alloy flange blanking plate for TS1 and RB cylinders. Also comes part of our complete test kit. ... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Chain sprocket adjustment alignment bracket (dial gauge separate) MBMRB0812K£49.14 £40.95This is a new quality precision CNC workshop tool from MB.This bridge bracket with the dial gauge fitted will tell you where you are when setting up your front sprocket to the rear... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Clutch holder, MBMRB0149£22.68 £18.90This is a MB steel clutch holder, which will let you safely and easily hold your clutch assembly while you undo and tighten the clutch nut. Using a screwdriver can damage your spr... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Con rod holding, MBMRB0156£28.48 £23.73This tool will work on any single cylinder vehicle. It is designed to rest on the base gasket face and hold your con-rod (and therefore your crank). The shape of it means it ... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Clutch compressor, MBMRB0150K£36.80 £30.67This is our MB Lambretta clutch compressing tool. Designed to safely compress your clutch while you change the clutch plates. It mounts across 2 studs on the crankcase side, so i... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Crankshaft drive side pulling sleeve, MBMRB0201£16.80 £14.00There is no point spending money on a crank that has been checked for alignment then going and hitting it with a hammer to fit it. This tool allows you to safely and easily pull... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Crankshaft and Drive bearing extractor and drive bearing puller, MBMRB0839K£40.04 £33.37We see a lot of damaged cranks where people have hit them with hammers to free them from the drive bearing.Here is a MB tool Designed by Mark Broadhurst where it safely presses cra... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Cylinder head dial gauge and bracket kit, MBMRB0433K£40.27 £33.56This Dial gauge bracket kit is designed to be used with any Lambretta, Vespa P range, T5 or small frame Vespa.It is designed to put your dial gauge right over the centre of the dom... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Cylinder head dial gauge bracket kit (no dial gauge) MBMRB0415K£21.37 £17.81This bracket kit is designed to be used with any Lambretta, P range, T5 or small frame Vespa. It is designed to put your dial gauge right over the centre of the dome of the piston ... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drive bearing fitting sleeve (used with crankshaft extracting tool, also rear hub bearing fitting) MBMBP0611£6.83 £5.69This is a spare sleeve that is sold separately to our crankshaft extracting tool. It can be used to pull the drive side bearing into position. ... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drive bearing pushing sleeve (crankshaft extractor) Pushes bearing outMBP0658£5.69 £4.74Lambretta Tool. Drive bearing pushing sleeve to work with the MB crankshaft extracting tool. This pushes the bearing out of the casing. This now comes in the Crankshaft tool - M... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drive and rear hub bearing holder, MBMRB1000K£24.58 £20.48MB-S designed drive and rear hub bearing tool. Designed so each bearing can be pushed on and held in place with the O ring, this allows you to easliy smear each bearing with seale... Learn MoreYou'll need: 1 of these
-
Tool, Dial gauge only, 30mm travel, MBMBL1390£18.90 £15.75This is a high quality 30mm movement dial gauge.It can be used with our cylinder head dial gauge bracket kit to set your timing from top dead center.... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drive side bearing fitting and removing, MBMRB0966£43.61 £36.34Theres plenty of ways to fit and remove a bearing, it's the same with a drive bearing. On a good casing if warmed enough a bearing will knock out and again if warm enough a bearin... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drive side crankshaft dummy bearing bush, stainless steel, MBMRB0981£17.64 £14.70This is a drive side crankshaft dummy bearing bush tool. Made in stainless steel for MB so it doesn't rust in the workshop over time. Basically it replaces a flywheel beari... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drive sprocket sleeve, extracting (puller) MBMBP0272£20.30 £16.92Drive Sprocket Sleeve removing pulling tool. Another MB product of an exact copy of an Innocenti item. A very handy tool for drive sprocket sleeves that become difficult ... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drift drive side and rear hub bearing, MBMRB0866£28.12 £23.43A simple workshop tool made by MB Scooters. This drift helps knock the drive side and rear hub bearing into place. On assembly of the engine, simply pre heat the bare engine casi... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drift end plate bearing, MBMRB0251£20.04 £16.70This MB tool is designed to make it easy and safe to refit the gearbox end plate bearing with out damaging the bearing. It's designed in such a way so it hits the out race not t... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drift flywheel side inner sleeve, MBMRB0254£21.94 £18.28This tool is designed to safely and easily fit the inner bearing sleeve from a flywheel bearing to the crank. You just fit the sleeve then tap it into place with this drift and ... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drift large magneto seal, MBMRB0202£12.85 £10.71Fitting the large oil seal into the magneto flange can be quite difficult so Mark came up with this tool to easily and squarely push the seal into place. It is made from hard ny... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Drift small magneto seal, MBMRB0593£10.08 £8.40Another tool designed by us to make fitting the small mag housing seal much easier. Offer the seal into position, fit the tool in place and press down straight, if need be - lig... Learn MoreYou'll need: 1 of these
-
Tool, Die handle for 8mm taping dies, MBMBU0924£5.93 £4.94Tool split die/die handle. Suits our MB 8 x 1mm die to clean up the drive side bolt threads. This comes with an inside diameter of 25mm.... Learn MoreYou'll need: 1 of these
-
Tool, Die handle for 12mm taping dies, MBMBU0925£8.53 £7.11Tool for dies with inside diameter of 38mm. Fits our 12 x 1mm left hand die for crankshaft flywheel threads. 12 x 1.25mm right hand for most fork link bolts. 12 x 1.5mm right h... Learn MoreYou'll need: 1 of these
-
Tool, Die, 8 x 1mm right hand thread fine pitch, Lambretta drive side bolt, MBMBU0922£5.80 £4.83Tool, die. 8 x 1mm right hand thread fine pitch for crankshaft drive side bolt threads Requires a universal Die holder. with an inside diameter of 25mm.... Learn MoreYou'll need: 1 of these
-
Tool, Die, 12 x 1mm left hand fine thread, Lambretta crankshaft flywheel side, MBMBU0923£8.20 £6.83Tool, die. 12 x 1mm Left hand fine thread for crankshaft flywheel side threads. Comes with outside diameter of 38mm and requires die holder MBU0925.... Learn MoreYou'll need: 1 of these
-
Tool, Die, 12 x 1.25mm, Lambretta fork link bolts, MBMBU0929£5.68 £4.73Tool, die, 12 x 1.25mm (for most fork link bolts) Use this with holding handle MBU0925 with 38mm inside diameter to run down old rusty or damaged fork bolts to clean the thread an... Learn MoreYou'll need: 1 of these
-
Tool, Engine mount, fits and removes Lambretta engine mounts (Silent blocks) MBMBL1575£47.15 £39.29Lambretta engine mounting (silent blocks) tool. Fits and removes all Series 1, 2 and 3 engine mounts, small or large type. Designed by Mark Broadhurst, zinc plated and chemically... Learn MoreYou'll need: 1 of these
-
Tool, Lambretta multi purpose 8mm T handle screws, pair, MBMRB0982PR£16.39 £13.66These are our multi purpose 8mm T handle screws. These are so handy, they can be used all the time on an engine build. Okay you can do all these jobs using a nut, spanner or... Learn MoreYou'll need: 1 of these
-
Tool, Feeler gauge with crank, 0.5 - 1.00mmMBU0894£11.76 £9.80Great set of feeler gauges with handy bend that makes them perfect for Lambretta gearboxes. But also cover points, spark plugs and other things. Measures from 0.005'' - 0.020''... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Final drive (puller) pulling sleeve, MBMRB0252K£13.56 £11.30It is important when fitting the layshaft and checking the tolerances in the gearbox, that the layshaft is pulled all the way into the rear hub bearing, as far as it will go. One ... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Flywheel puller (extractor) single (Italian/Indian) MBMBP0361£11.98 £9.98Single ended flywheel extractor. The hex head of the extractor bolt is the same size as the head of a flywheel nut which means you only need one socket to undo a flywheel instead o... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Flywheel puller (extractor) Spanish flywheels onlyMBL0180£19.80 £16.50Flywheel puller for Spanish flywheels only (30mm x 1.5mm thread)... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Flywheel holder (holding) double ended, MBMRB0253£24.20 £20.17This tool will hold 90% of Lambretta flywheels. It is double ended and will hold normal Italian Series 3 type flywheels as well as the AF/J range, Early Motoplat and Indian elec... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Flywheel holder (holding) for Vape Ignitions, SIPSI00042£18.00 £15.00Lambretta Flywheel holding tool for Vape Ignitions.... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Flywheel holder (holding) for bgm and Varitronic flywheels, MBMBGM0407£11.69 £9.74Flywheel holding tool for Bgm and Varitronic flywheels, holds the flywheel on the main centre nut to avoid any damage to the flywheel fins. For using with long Gp/Sx type engine m... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Kickstart modification tool, MBMBP0124£35.46 £29.55Crankcase side kick start modification tool. This will safely machine the side casing on Series1, 2 and early engines with the weaker kickstart shaft so the stronger GP kickstart ... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Leak down pressure test set up kit, MBMBP0672K£65.12 £54.27Complete top end pressure test kit from MB Scooters. Kit comes complete with Pump and gauge 25/30mm Dellorto inlet manifold alloy bung, MB 34/35mm Dellorto/Mikuni inlet manif... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Mag housing crankshaft dummy bearing bush, stainless steel, MBMRB0980£17.64 £14.70This is a mag side crankshaft dummy bearing bush tool. Made in stainless steel for MB so it doesn't rust in the workshop over time. Basically it replaces a flywheel bearing... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Rear hub bearing fitting and removing, MBMRB0967£49.50 £41.25Theres plenty of ways to fit and remove a bearing, it's the same with a rear hub bearing. On a good casing if warmed enough a bearing will drop or knock out and again if warm enou... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Rear hub bearing sleeve (works with crank extractor, bolt) MBMBP0618£12.17 £10.14This sleeve can be used with the crankshaft fitting tool bolt and drive bearing fitting sleeve to drawn in the rear hub bearing into the casing.... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Rear hub puller (extractor) S1/2/3, MBMBP0358K£38.16 £31.80Using this tool is the best and safest way to remove your Series 1, 2 and 3 Lambretta rear hubs. You simply bolt it to your hub with the two/three bolts then turn the large bolt w... Learn MoreYou'll need: 1 of these
-
Tool, Spark plug dead stop, adjustable, MBMBP0704£28.36 £23.63This is a very handy little Top Dead Center finding tool designed and made by MB Scooters. Design to work with Lambrettas with engines in or out of the frame. With the spark plug... Learn MoreYou'll need: 1 of these
-
Tool, Spark plug socket, MBMBP0267£19.57 £16.31It's a well known fact the Lambretta spark plug is in an awkward position and hard to get to, especially when a TS1, RB or Monza cylinder is fitted. So Mark Broadhurst came up w... Learn MoreYou'll need: 1 of these
-
Tool, Stud fitting, installer / installation tool 6x1.0mm, MBMBP0593£5.59 £4.66A simple 6mm stud fitting/installation tool. Finger screw in your stud, use some loctite on the thread to be fitted in the casing then screw the stud into the casing until it... Learn MoreYou'll need: 1 of these
-
Tool, Stud fitting, installer / installation tool 7x1.0mm, MBMBP0594£5.59 £4.66A simple 7mm stud fitting/installation tool. Finger screw in your stud, use some loctite on the thread to be fitted in the casing then screw the stud into the casing until it... Learn MoreYou'll need: 1 of these
-
Tool, Stud fitting, installer / installation tool 8x1.25mm, MBMBP0595£5.59 £4.66A simple 8 x 1.25mm stud fitting/installation tool. Finger screw in your stud, use some loctite on the thread to be fitted in the casing then screw the stud into the casing u... Learn MoreYou'll need: 1 of these
-
Tool, Stud fitting, installer / installation tools, 6x1mm, 7x1mm, 8x1.25mm, MBMBP0596S£16.78 £13.98A set of simple MB made - 6 x 1mm, 7 x 1mm, 8 x 1.25mm stud fitting/installation tools. Finger screw in your stud, use some loctite on the thread to be fitted in the casing t... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, Timing disc, metal, MBMRB0662£20.30 £16.92This timing disc has been specially designed by us for using on Lambrettas and can be used on engines fitted with GP crankshafts.It is made in aluminium for durability.It is marked... Learn MoreYou'll need: 1 of these
-
Lambretta Tool, T bar extractors, magneto housing and end plate, pair, MBMRB0155£15.76 £13.13Another tool copied from the original with a slight MB improvement. We remade these T bar extractors in slightly different lengths so the handles don't foul in use unlike on th... Learn MoreYou'll need: 1 of these
-
Tool, Tap T handle Small, fits 3, 3.5, 4, 5, 6, 7, 8mm taps, MBMBU0926£8.32 £6.93Tapping T handle small to fit these taps; 3mm 3.5mm 4mm 5mm 6mm 7mm 8mm ... Learn MoreYou'll need: 1 of these
-
Tool, Tap T handle, Large, fits 5, 6, 7, 8, 10, 12mm taps, MBMBU0927£10.46 £8.72Tapping tool T handle, adjustable to fit taps; 5mm 6mm 7mm 8mm 10mm 12mm ... Learn MoreYou'll need: 1 of these
-
Tool, Tap 4 x 0.7mm, MBMBU0913£4.54 £3.78Universal tapping tool made for MB Scooters. 4mm diameter x 0.7mm thread. Ideal for cleaning/tapping out threads out on a Lambretta. Series 1/2/3 horncasts Series 1/2 h... Learn MoreYou'll need: 1 of these
-
Tool, Tap 5 x 0.8mm, MBMBU0914£4.54 £3.78Universal tapping tool made for MB Scooters. 5mm diameter x 0.8mm thread. Ideal for cleaning/tapping out threads out on a Lambretta. Series 1/2/3 horncast Series 1/2/3 ... Learn MoreYou'll need: 1 of these
-
Tool, Tap 6 x 1mm, MBMBU0915£5.17 £4.31Universal tapping tool made for MB Scooters. 6mm diameter x 1mm thread. Ideal for cleaning/tapping out threads out on a Lambretta. Series 1/2/3 engine threads Series 1/... Learn MoreYou'll need: 1 of these
-
Tool, Tap 7 x 1mm, MBMBU0916£6.18 £5.15Universal tapping tool made for MB Scooters. 7mm diameter x 1mm thread. Ideal for cleaning/tapping out threads out on a Lambretta. Series 1/2/3 end plate threads Series 1/2/3... Learn MoreYou'll need: 1 of these
-
Tool, Tap 8 x 1mm, MBMBU0917£7.19 £5.99Universal special tapping tool made for MB Scooters. 8mm diameter x 1mm thread. Ideal for cleaning/tapping out threads out on a Lambretta. Drive side crankshaft bolt hol... Learn MoreYou'll need: 1 of these
-
Tool, Tap 8 x 1.25mm, MBMBU0918£6.80 £5.67Universal tapping tool made for MB Scooters. 8mm diameter x 1.25mm thread. Ideal for cleaning/tapping out threads out on a Lambretta. Series 1/2/3 engine casing exhaust mounts... Learn MoreYou'll need: 1 of these
-
Tool, Tap 10 x 1mm Left hand, MBMBU0919£12.85 £10.71Universal special tapping tool made for MB Scooters. 10mm diameter x 1mm thread. Ideal for cleaning/tapping out threads out on a Lambretta. Front and rear hub stud threads. Th... Learn MoreYou'll need: 1 of these
-
Tool, Tap 10 x 1.5mm, MBMBU0920£8.57 £7.14Universal tapping tool made for MB Scooters. 10mm diameter x 1.5mm thread. Ideal for tapping out threads out on a Lambretta using a MB stepped stud or threaded insert. Series ... Learn MoreYou'll need: 1 of these
-
Tool, Tap 12 x 1.5mm, MBMBU0921£9.46 £7.88Universal tapping tool made for MB Scooters. 12mm diameter x 1.5mm thread. Ideal for tapping out threads out on a Lambretta using a MB stepped stud and threaded MB insert. Ser... Learn MoreYou'll need: 1 of these