Rebuild List: Rebuild List Fasteners Studs
-
Universal Thread lock, 6ml tube (loctite)MBU0851£6.32 £5.276ml tube of thread lock, ideal to use on studs, nuts and head gaskets.... Learn MoreYou'll need: 1 of these
-
Tool, Stud fitting, installer / installation tool 6x1.0mm, MBMBP0593£5.59 £4.66A simple 6mm stud fitting/installation tool. Finger screw in your stud, use some loctite on the thread to be fitted in the casing then screw the stud into the casing until it... Learn MoreYou'll need: 1 of these
-
Tool, Stud fitting, installer / installation tool 7x1.0mm, MBMBP0594£5.59 £4.66A simple 7mm stud fitting/installation tool. Finger screw in your stud, use some loctite on the thread to be fitted in the casing then screw the stud into the casing until it... Learn MoreYou'll need: 1 of these
-
Tool, Stud fitting, installer / installation tools, 6x1mm, 7x1mm, 8x1.25mm, MBMBP0596S£16.78 £13.98A set of simple MB made - 6 x 1mm, 7 x 1mm, 8 x 1.25mm stud fitting/installation tools. Finger screw in your stud, use some loctite on the thread to be fitted in the casing t... Learn MoreYou'll need: 1 of these
-
Tool, Stud fitting, installer / installation tool 8x1.25mm, MBMBP0595£5.59 £4.66A simple 8 x 1.25mm stud fitting/installation tool. Finger screw in your stud, use some loctite on the thread to be fitted in the casing then screw the stud into the casing u... Learn MoreYou'll need: 1 of these
-
Stud 4x21mm - 5x2x10mm, Lambretta magneto housing sealing plate, MBMBFST4X21SS£0.77 £0.64A special MB made stainless steel stud to fit into a mag housing, used with our special MB nuts these make life easier when working on a mag housing and stator plate when the engin... Learn MoreYou'll need: 1 of these
-
Stud 6x27mm - 13 x 6 x 8mm, Lambretta electronic mounting brackets, stainless steel, MBMBFST6X27SS£0.65 £0.54Lambretta Stud, 6mm - 13 x 6 x 8mm, for CDI and Regulators on MB electronic mounting brackets, Stainless steel, MB... Learn MoreYou'll need: 1 of these
-
Stud 6x21mm - 7x4x10mm, Lambretta rear hub plate, linkage tie bar, stainless steel, MBMBFST6X21SS£1.15 £0.96This stainless steel stud is designed to fit on the casing where the rear hub bearing sits and holds on the plate which holds the rear hub bearing in. You need four per casing. ... Learn MoreYou'll need: 4 of these
-
Stud 6x25mm - 10x5x10mm, Lambretta magneto housing, stainless steel, MBMBFST6X25SS£0.84 £0.70This remade stainless steel stud is designed to be used to secure the magneto housing to the engine casing. It can also be used with our adjuster block to attach that to the cas... Learn MoreYou'll need: 3 of these
-
Stud 6x33mm - 6x6x21mm, Lambretta crankcase side and TS1 inlet manifold, engineers, stainless steel, MBMBFST6X33TS1£1.44 £1.20This stud can be used to secure the crankcase side but is also as used as an inlet stud on our TS1 manifolds. It is made from stainless steel. 6mm x 6 - 6 - 21mm... Learn MoreYou'll need: 1 of these
-
Stud 6x37mm - 16x10x11mm, Lambretta crankcase side, stainless steel, MBMBFST6X33SS£0.70 £0.58This stud is for the crankcase side, you need 14 for most crankcases. If youre using a Clubman then you use 13 and the longer tailpipe stud.We've redesigned these so the long end ... Learn MoreYou'll need: 14 of these
-
Stud 6x37mm - 12x13x15mm, Lambretta crankcase side tail pipe, stainless steel, MBMBFST6X37SS£0.78 £0.65This remade stainless steel stud is used to secure the crankcase side at the point below the kick-start when standard exhausts mount to the casing. 6mm x 12 - 13 - 12mm... Learn MoreYou'll need: 1 of these
-
Stud 6x42mm - 11x20x11mm, Lambretta crankcase side with external 6 plate clutch, stainless steel, MBMBFST6X42SS£1.33 £1.11This remade stainless steel stud is designed to be used to secure the crankcase side where a 10mm thick pack plate has been used. You would need 14 per engine casing. It can also ... Learn MoreYou'll need: 14 of these
-
Stud 6x51mm - 12x23x16mm, Lambretta crankcase side stud with Dev-Tour bracket, stainless steel, MBMBFST6X51SS£1.34 £1.12This remade stainless steel stud is designed to be used to secure the crankcase side where one of our rear exhaust brackets is fitted. It is designed to fit where a 10mm crankcase... Learn MoreYou'll need: 1 of these
-
Stud 7x34mm - 12x10x12mm, Lambretta short inlet, stainless steel, MBMBFST7X34SS£0.80 £0.67This remade stainless steel stud is designed for use with standard type cylinders where it can be used as the short inlet stud. 7mm x 12 - 10 - 12mm... Learn MoreYou'll need: 1 of these
-
Stud 7x34mm - 17x7x10mm, Lambretta exhaust port, oval, RT inlet, stainless steel, MBMBFST7X34SSMB£0.92 £0.77New longer MB exhaust port stud to suit the new longer stronger MB brass nuts. Also used for Race-Tour small inlet studs.... Learn MoreYou'll need: 1 of these
-
Stud 7x36mm - 17x7x12mm, Lambretta round exhaust port, stainless steel, MBMBFST7X36SSMB£1.10 £0.92New longer stud to suit MB new longer and stronger brass exhaust nut.... Learn MoreYou'll need: 1 of these
-
Stud 7x50mm - 15x15x20mm, Lambretta long inlet, stainless steel, MBMBFST7X50SS£0.96 £0.80This remade stainless steel stud is designed to be used as the long inlet stud on a piston ported type Lambretta cylinder. 7mm x 15 - 15 - 20mm... Learn MoreYou'll need: 1 of these
-
Stud 8x45mm - 17x11x17mm, Lambretta crankcase side exhaust mount, stainless steel, MBMBFST8X45SS£1.07 £0.89This stud is used to hold the exhaust bracket to the main engine casing. You need two per engine casing. 8mm x 17 - 11 - 17mm... Learn MoreYou'll need: 2 of these
-
Stud, 8x53mm, Lambretta cylinder for RT kits, Race-Tour MBMBFST8X53SC£1.06 £0.88This stud has been specially designed to be used as an opgrade on Race-Tour type cylinders to secure the head instead of the screws provided. You need 4 per cylinder. 15 x 12 x 2... Learn MoreYou'll need: 1 of these
-
Stud, 8x166mm Lambretta cylinder longer relieved, Race-Tour MBMBP0513£6.12 £5.10We think this is the ultimate in cylinder stud design. Made from high tensile steel. Fits all Lambrettas cylinders - small and large block, works with shortened cylinders and wor... Learn MoreYou'll need: 1 of these
-
Stud, 12x60mm - 20x20x20mm, Lambretta disc hub locating half, stainless steel, MBMBFST12X60£3.29 £2.74This is a remade stainless disc locating stud. It is fitted to the standard Lambretta disc hub backplate. 12mm x 20 - 20 - 20mm... Learn MoreYou'll need: 1 of these
-
Lambretta Fork link damper stud, each, stainless steel, MBMBP0047£4.85 £4.04This is the MB disc link damper stud redesigned to straighten up dampers to the forks. Made in stainless steel. It is suitable for Italian type disc links and MB Drum and Disc li... Learn MoreYou'll need: 1 of these