This drift tool is designed to safely and easily remove the two fork link bushes.    It is stepped to allow the inner one to be... [more]

This tool is designed and made by MB Scooters, loosely based on the genuine Innocenti item but with improvements. Its designed to safely and easily help... [more]

This tool is designed to safely and easily refit front hub bearings and seals helping you to put them in straight without damaging bearings,... [more]

This tool, made for MB, is designed to safely and easily remove and refit the bush for the rear brake pedal. It also removes the... [more]

This tool made by us (MB) is designed to turn the steering bearing lock nut (the one that rests on top of the upper... [more]

This tool made by us (MB) is designed to turn the steering bearing locking ring (the one that rests on top of the locking... [more]

This is a pair of steering bearing tools to tighten the Lambrettta steering bearings lock nuts.   Chrome plated with a hole in the handle... [more]

This is a MB steel clutch holder, which will let you safely and easily hold your clutch assembly while you undo and tighten the... [more]

This is our MB Lambretta clutch compressing tool.    Designed to safely compress your clutch while you change the clutch plates.    It mounts... [more]

Another tool copied from the original with a slight MB improvement.    We remade these T bar extractors in slightly different lengths so the handles ... [more]

This tool will work on any single cylinder vehicle.    It is designed to rest on the base gasket face and hold your con-rod (and therefore... [more]

This is a copy of the original tool as supplied with all new Lambrettas.    It fits in a small hole under the rear of your... [more]

There is no point spending money on a crank that has been checked for alignment then going and hitting it with a hammer to... [more]

Fitting the large oil seal into the magneto flange can be quite difficult so Mark came up with this tool to easily and squarely... [more]

This MB tool is designed to make it easy and safe to refit the gearbox end plate bearing with out damaging the bearing.    It's designed... [more]

It is important when fitting the layshaft and checking the tolerances in the gearbox, that the layshaft is pulled all the way into the... [more]

This tool will hold 90% of Lambretta flywheels.    It is double ended and will hold normal Italian Series 3 type flywheels as well as the... [more]

This tool is designed to safely and easily fit the inner bearing sleeve from a flywheel bearing to the crank.    You just fit the sleeve... [more]

This bracket kit is designed to be used with any Lambretta, P range, T5 or small frame Vespa.   It is designed to put your... [more]

This Dial gauge bracket kit is designed to be used with any Lambretta, Vespa P range, T5 or small frame Vespa.    It is... [more]

This timing disc has been specially designed by us for using on Lambrettas and can be used on engines fitted with GP crankshafts.   ... [more]

Another tool designed by us to make fitting the small mag housing seal much easier.    Offer the seal into position, fit the tool in place... [more]

A simple 7mm stud fitting/installation tool. Finger screw in your stud, use some loctite on the thread to be fitted in the casing then screw the... [more]

A simple 8 x 1.25mm stud fitting/installation tool. Finger screw in your stud, use some loctite on the thread to be fitted in the casing then... [more]

A set of simple MB made - 6 x 1mm, 7 x 1mm, 8 x 1.25mm stud fitting/installation tools. Finger screw in your stud, use some... [more]

A simple 6mm stud fitting/installation tool. Finger screw in your stud, use some loctite on the thread to be fitted in the casing then screw the... [more]

Single ended flywheel extractor.  The hex head of the extractor bolt is the same size as the head of a flywheel nut which means... [more]

A simple workshop tool made by MB Scooters. This drift helps knock the drive side and rear hub bearing into place. On assembly of the engine,... [more]

... [more]

These are our multi purpose 8mm T handle screws.  These are so handy, they can be used all the time on an engine build. Okay... [more]

It's a well known fact the Lambretta spark plug is in an awkward position and hard to get to, especially when a TS1, RB... [more]

Drive Sprocket Sleeve removing pulling tool.    Another MB product of an exact copy of an Innocenti item.    A very handy tool for drive sprocket sleeves that... [more]

This is a new quality precision CNC workshop tool from MB.    This bridge bracket with the dial gauge fitted will tell you where... [more]

Lambretta engine mounting (silent blocks) tool. Fits and removes all Series 1, 2 and 3 engine mounts, small or large type. Designed by Mark Broadhurst, zinc... [more]

Crankcase side kick start modification tool.    This will safely machine the side casing on Series1, 2 and early engines with the weaker kickstart... [more]

We see a lot of damaged cranks where people have hit them with hammers to free them from the drive bearing.    Here is... [more]