The nicest stator I have ever purchased, top quality craftsmanship, works great,
Thank you very much MRB
I have been running one of these for a while now.
I cannot recommend highly enough
Another fabulous product
Thanks MB
Great product, great service and quick postage to Australia.
A solid well made stator
An absolute must to a Lambretta electrical system
It's transformed mine after an Indian stator before this.
Great piece of kit, well made and good quality
Great product. Fitted well. The extra packing pieces are engineered really well. Made setting the pick up height really easy.
The difference between this and my previous stators is nothing less than remarkable. Its like I have a different scooter. My scooter starts with the slightest of kicks and I no longer have to twist the throttle frantically to keep the engine idling. You really do get what you pay for.
scooter purring like a kitten , highly recommended
Would of given it ten stars brilliant bit of kit keep up the good work will be back for sure
fast delivery thankyou. at present havent fitted it
Looks well made easy enough to fit.
Starts and runs Great. Very happy with it.
Looks a well built piece all solder joints seal
Was going to convert to dc but looks like not built to be messed with
If you would like to ask us a question about this product, please feel free to click here to ask a Question Now!
Grant M on 07 Jan 2023 asked "Trouble shooting, scooter not revving out at high revs. Running BGM stator with an indian long fin flywheel & want to check the alignment of pick up to stator. Am i just ensuring that both pick up sensors are aligning with flywheel magnets? And if not i use the packets supplied to increase height on pick up? Thanks, G."
MB Scooters Ltd replied: Thats correct
Peter K on 07 Oct 2022 asked "Hi have low voltage from lighting circuit om bgm stator on lambretta what should resistance be between white and yellow wires ???
Thank you "
MB Scooters Ltd replied: Should be about 2.25 ohms or 1.14mH
David H on 21 Apr 2022 asked "I have bought this stator and the BGM GP flywheel ,but when fitted I am getting no spark any ideas on what I need to check .Could it be the CDI .My Scooter is a li 150 with GP crank and your 195/225 race tour kit."
MB Scooters Ltd replied: We've had no issue from new flywheels and stators. I can check them, but check the CDI first, and trapped wire inside the flywheel area and check youve fitted the correct colours in the CDI
Fergus O on 04 Feb 2021 asked "Might be silly, but can I run this stator with a flywheel that spins the other way i.e. An LD ( or an ISO )
Cheers"
MB Scooters Ltd replied: No it wont work
John M on 19 Oct 2020 asked "Good afternoon,
I have an AF Mid Weight Electronic Flywheel GP Type, would this flywheel be suitable for this particular stator.
Thank you.
John J"
MB Scooters Ltd replied: Yes its a straight fit
Paul on 08 Oct 2014 asked "Can I run this stator with the older type rectifier, or do I need the newer type? "
MB Scooters Ltd replied: Yes it is a straight swap
George s on 23 May 2014 asked "Hi can you tell me have you improved your stator plate for a AF fly wheel as I am thinking of buying one "
MB Scooters Ltd replied: They are supposed to be now
Richard on 09 Aug 2011 asked "How has the stator been improved, and what wattage is it now putting out?"
MB Scooters Ltd replied: Tested and rewired to get the most power output from the flywheels magnetism. Theres talk of 120 Watts, but this is the limit set by the magnets.
Mark D on 15 May 2011 asked "I have a question about "Electronic stator plate, BGM type, 120W, version 2"
What flywheel would you recommend for this when using with an Imola kit and Agusto retard unit -- looking for alternative to varitronic."
MB Scooters Ltd replied: The BGM stator works well with the Indian flywheels for this purpose.
Russ on 03 Jun 2010 asked "I have a question about "Electronic stator plate, BGM type, 120W version"Hi, can you tell me why you advise to not use with the af later type flywheel""
MB Scooters Ltd replied: There are difference with lots of flywheels, some can produce a miss fire, the AF flywheel has brass rivets which seem to cause a miss fire, we are working to improve the BGM stator to improve them and work with all flywheels for the future.
Kevin W on 14 Mar 2010 asked "I have a question about "Electronic stator plate, BGM type, 120W version"
Hi Mark,
Can I use this stator with my original gp150 Italian flywheel, as I'm still running 6v points electrics ? Thanks for any advice."
MB Scooters Ltd replied: No, this is a electronic type stator, you require a points type stator or you could swap for a complete electronic kit.
Ian m on 11 Dec 2008 asked "Hi Mark,
How does the standard 12V ac regulator stand up to the increased output? Is there any reduction in lifespan?
Thanks,
ian"
MB Scooters Ltd replied: The standard regulator is well within the safe working operation of the 120 watt stator.
Dave W on 31 Jul 2008 asked "I have a question about "Electronic stator plate, BGM type, 120W version"
Recently purchase from you a new Ducati CDI and regulator along with your mounting kit . It looks great as I can put the new items under the rear frame where they should be.
It was a tough job, especially when I replaced all of the wiring without removing the floor boards or legshield!
Anyway, when I looked at the old stator wire sleeving, I noticed two things: The white wire in the sleeve was actually broken and was just sitting in the stator loom. Secondly, the wire loom was not long enough to now reach the new CDI with its new location, as my old wiring system had an ugly unction box on the panel bracket
Can I fit the BGM 120 v stator to my Indian GP with an indian flywheel? Is the BGM stator wire long enough to reach the CDI in its new position? What tools would I need to install it?
Does the BMG stator have long enough wiring to reach the CDI (right side) without the need for a junction box by the stator?
If I make the purchase, what other tools would I need for the install and do you carry them?"
MB Scooters Ltd replied: The BGM stator comes with long wires that can fit anywhere in the area where our mounting brackets fit.
Using our loom means you do not require the junction box.
To fit a new stator you will require a flywheel holding tool and flywheel extractor.
You will also require some timing equipment.
Refer to the Spanners manual on how to do the job.
If you feel something is not correct with this product description or image then please contact us using the same link