Parts index
We stock over 25 GP bodywork
This section contains metal bodywork suitable for GP/DL Lambretta scooters. Unless specified it is manufactured in India.
MBFSP
These clips are used to hold the plastic strips to your rear floorboards. You need 10 per scooter. A useful tip when fitting them... [more]
MBL0207
This is an Indian GP front mudguard.
It can be fitted to any Series 3 Lambretta.
Comes painted in primer.
... [more]
MBL0257
This item is an Indian GP horncast. It comes in a primer type finish and goes not include the grille or the badge.... [more]
MBL0292
This clamp secures the beading at the top of the legshields of all Series 3 scooters. You need two per scooter. They are... [more]
MBL0297PR
These secure the legshield beading at the bottom of GP legshields. They get their name because they are shaped like a sharks tooth. They... [more]
MBL0362
This is an NOS SIL GP rear runner board (flywheel side). It can be used on any Series 3 without any problems. These are the... [more]
MBL0363
This is a NOS SIL GP rear runner board (kick-start side). It can be used on any Series 3 without any problems. These are the... [more]
MBL0370
This is a set of quality European remade alloy channels to suit all Series 3 scooters.... [more]
MBL0566
This little bush is used to hold the Innocenti rear frame badge in place on a GP. Another quality remade part from MB. Two required.... [more]
MBL0781PR
This is a pair of black plastic grilles for GP side panels.... [more]
MBL0848
The right size alloy rivet to secure your toolbox lock.... [more]
MBL0886S
This is a set of excellent remade alloy end caps, to go on the end of the alloy channels on a GP.... [more]
MBL1157S
Panel theft is a sad event that seems to be happening a lot again as prices of scooters creep up. These are high... [more]
MBP0053
This remade MB bracket is laser cut from stainless steel and is used to secure the clips that hold the panels on GP... [more]
MBP0068S
This is a set of three toolbox tie rods, remade by MB in stainless steel. Fits all Lambretta Series 1, 2 and 3... [more]
MBP0075
This is a MB remade stainless steel side panel clip for a GP (or any late Lambretta with clip on panels). It is the left hand... [more]
MBP0076
This is a MB stainless steel side panel clip for a GP (or any late Lambretta with clip on panels). It is the right hand... [more]
MBP0089
This is the one fastener that you really notice looking at a Lambretta from the front and we though it was a shame to... [more]
MBP0219K
You can take the guesswork out of rebuilding your Series 3 Lambrettas by using our popular bodywork hardware fastener kit. It includes ... [more]
MBP0220K
This kits contains all the stainless steel fasteners needed to fit a Series 3 horncasting. The fasteners in this kit are already included in the... [more]
MBP0223K
This handy kit contains all the fasteners needed to secure the side panel clip plates on a Series 3 Lambretta.... [more]
MBP0100K
This MB remade kit contains the 2 clips that your side panel clip onto the clip plate that holds the clips to the frame and... [more]
MBL1384
Spare alloy end cap to suit Gp legshields. Un supported type. ... [more]
MBL0456
Last stock of SIL GP right hand side metal side panels. Look a little rough with over spray and runs but are good solid panels,... [more]
MBL0671
NOS SIL Gp left hand side panel in metal. They look a little rough with over spray and runs but are very good solid panels... [more]