This red petrol tap sticker goes on the inside bottom face of the petrol tap.... [more]

Amongst many applications this fastener can specifically be used as a Lambretta rear shocker nut.... [more]

Amongst many applications this fastener can specifically be used under the rear shocker and engine bar nuts. Specially made in stainless steel for MB Scooters.... [more]

This pin hold the petrol tank flap to the frame. Brass, UK made ... [more]

This is a plastic petrol flap for GP scooters.... [more]

This a small petrol tank rubber buffer.   Two are fitted on the side of the tank under the tank strap to space the... [more]

This buffer sits at the back of the tank on the frame arm.   Two are needed per scooter.   Series 3 Gp type... [more]

These black bungs are designed to neatly fill the holes in the back of your Series 3 frame.... [more]

These grey bungs are designed to neatly fill the holes in the back of your Series 3 frame.... [more]

This is a pair of quality remade Italian grey side panel rubbers for Series 1/2 & 3 scooters.... [more]

This buffer fits into the frame on your Series 3 to stop the toolbox door rattling.  You need two.... [more]

This buffer fits into the frame on your Series 3 to stop the toolbox door rattling.  You need two. Slighty redesigned by MB to mak efitting... [more]

This is a lock for a Series 3 toolbox door.    It comes with 2 keys.... [more]

This black grommet protects your frame where the petrol tap lever does through it and stops the lever rattling.... [more]

This rubber fits around the toolbox to cushion it as it rests on the frame. Another top product made for MB. Top tip, use a heat... [more]

This is a remade Italian rear frame badge holder, suitable for all Series 3 scooters except the GP.  It is designed to hold a plastic... [more]

This is a standard type metal petrol flap for Li, Sx, Tv frames. Made in stainless steel... [more]

This is a metal petrol flap with a lock and two keys.   GP only.... [more]

This bung fits into the frame to secure the toolbox tie rods to stop them rattling.  You need two per scooter.... [more]

Lambretta Rear shocker shaft mount, on engine casing (stud) made in Stainless steel to stop rusting made for MB Scooters.  You will need a hydraulic... [more]

Panel theft is a sad event that seems to be happening a lot again as prices of scooters creep up.    These are high... [more]

This is the upper toolbox tie rod remade in stainless steel.    You need one per scooter. An MB remade product.... [more]

This is the lower toolbox tie rod remade in stainless steel.    You need two per scooter. An MB product.... [more]

We were so disappointed with the variable quality of the toolbox lid hinge pins that we had a MB version made in stainless steel.    These... [more]

This spring steel clip holds the side panel buffers to the rear floorboard support arms on a Series 3. Another slightly re designed and improved... [more]

Remade by MB this stainless steel horn bracket suits all late type Series 3 frames.... [more]

BGMs excellent top quality totally adjustable rear shock absorber (damper)    Designed as a perfect fit for all Lambretta Scooters.    Adjustable ride height... [more]

16 x 1.5mm Nyloc nut used for rear shock absorbers and engine bars. Perfect fitting MB nyloc nut in stainless steel.    The nyloc nut... [more]

This special stainless steel washer was designed by Mark Broadhurst to work with BGM and other shockers.    It fits over the frame when... [more]

... [more]

Lambretta Stand cross member for all Series 3's.... [more]

A pair of MB made stainless steel stand frame strengtheners. Suits all Series 3 Lambrettas.... [more]

Series 2 toolbox lock with 2 keys.... [more]